[gate-users] Root Output

[Claude Comtat]

Dear Long,

well, this is something else. It's normal that you do not have 
visualization when running Gate in batch mode ! You have to run Gate 
interactively to have the visualization running as well.

Regards,

Claude

null99 at mails.tsinghua.edu.cn wrote:

>Dear Claude,
>
>Both can't work, I think. 
>
>At first, I have ROOT output only, GATE can't produce opengl window in batch mode.
>Then add the ROOT real-time ploter option and rebuild GATE and Geant4, Gate still
>can't produce OpenGL window in batch mode.
>
>However, both can produce gl window when not in batch mode. weird... :-(
>
>Regards,
>
>Long
>
>
>In your mail:
>
>>From: Claude Comtat <comtat at ieee.org>
>>Reply-To: GATE feedback and helpline for Users <gate-users at lphe1pet1.epfl.ch>
>>To: gate-users at lphe1pet1.epfl.ch
>>Subject: Re: [gate-users] Root Output
>>
>>Dear Simone, Els and Long,
>>
>>strange behavior; here, with Redhat 9.0 and root 3.10, both OpenGL 
>>visualization and root outputs are working together. I do not think we 
>>tried with Redhat 8 (jumped directly from 7.3 to 9.0)
>>
>>When you said "root output", did you refer to both "root output" 
>>(G4ANALYSIS_USE_ROOT) and "root real-time plotter" 
>>(G4ANALYSIS_USE_ROOT_PLOTTER) ? If you disable only the root real-time 
>>plotter, does OpenGL work ?
>>
>>Could you please give us
>>
>>1) your env_gate.csh file
>>2) the full output of "source env_gate.csh"
>>3) your macros
>>4) the full output of Gate running
>>
>>Best regards,
>>
>>Claude
>>
>>Els Wieërs wrote:
>>
>>>Dear all,
>>>
>>>It's all in the macro. But when I run Gate I get the following errors:
>>>***** COMMAND NOT FOUND </gate/output/root/enable> *****
>>>***** Command ignored *****
>>>***** COMMAND NOT FOUND </gate/output/root/setFileName MyRootFileName test1>
>>>*****
>>>***** Command ignored *****
>>>***** COMMAND NOT FOUND </gate/output/root/setRootSinglesFlag 1> *****
>>>***** Command ignored *****
>>>etc...
>>>It's obivious that the Root output doesn't work although everything should
>>>be installed just right (see mail below)
>>>Any other suggestions?
>>>Greets
>>>Els
>>>
>>>ps: the macro is in the attachement
>>>
>>>Dear all,
>>>
>>>Sorry, my fault. It should be "might" can't work with root output enabled.
>>>
>>>It may caused by difference between Redhat 8.0 and Redhat 9.0 (purly guess).
>>>
>On
>
>>>Redhat 8.0, it can't work ( two of my Redhat 8.0 Linux box can't work ).
>>>
>Redhat
>
>>>9.0, I don't know, but I remember David Schottlander (dcs at robots.ox.ac.uk) had
>>>told me that there is no problem on his Redhat 9.0 box.
>>>
>>>Regards,
>>>
>>>Long
>>>
>>>Dear Claude,
>>>
>>>I can't run simultaneous OpenGL and root output either; please see the
>>>discussion "vis problem: Command not found".
>>>
>>>Best regards,
>>>Simone
>>>
>>>
>>
>>
>>_______________________________________________
>>gate-users mailing list
>>gate-users at lphe1pet1.epfl.ch
>>http://lphe1pet1.epfl.ch/mailman/listinfo/gate-users
>>
>
>
>_______________________________________________
>gate-users mailing list
>gate-users at lphe1pet1.epfl.ch
>http://lphe1pet1.epfl.ch/mailman/listinfo/gate-users
>
>