[gate-users] Root Output

[Schmidtlein, Ross/Medical Physics]

Hi Long,

I don't think GATE can produce an OpenGL window in batch mode in any distribution or release.  I don't think that this is an error, just the way GATE was built.

Cheers,

ross

-----Original Message-----
From: gate-users-bounces at lphe1pet1.epfl.ch [mailto:gate-users-bounces at lphe1pet1.epfl.ch] On Behalf Of null99 at mails.tsinghua.edu.cn
Sent: Tuesday, August 24, 2004 10:05 AM
To: gate-users at lphe1pet1.epfl.ch
Subject: Re: [gate-users] Root Output


Dear Claude,

Both can't work, I think. 

At first, I have ROOT output only, GATE can't produce opengl window in batch mode. Then add the ROOT real-time ploter option and rebuild GATE and Geant4, Gate still can't produce OpenGL window in batch mode.

However, both can produce gl window when not in batch mode. weird... :-(

Regards,

Long


In your mail:
>From: Claude Comtat <comtat at ieee.org>
>Reply-To: GATE feedback and helpline for Users 
><gate-users at lphe1pet1.epfl.ch>
>To: gate-users at lphe1pet1.epfl.ch
>Subject: Re: [gate-users] Root Output
>
>Dear Simone, Els and Long,
> 
> strange behavior; here, with Redhat 9.0 and root 3.10, both OpenGL
> visualization and root outputs are working together. I do not think we 
> tried with Redhat 8 (jumped directly from 7.3 to 9.0)
> 
> When you said "root output", did you refer to both "root output"
> (G4ANALYSIS_USE_ROOT) and "root real-time plotter" 
> (G4ANALYSIS_USE_ROOT_PLOTTER) ? If you disable only the root real-time 
> plotter, does OpenGL work ?
> 
> Could you please give us
> 
> 1) your env_gate.csh file
> 2) the full output of "source env_gate.csh"
> 3) your macros
> 4) the full output of Gate running
> 
> Best regards,
> 
> Claude
> 
> Els Wieërs wrote:
> 
> >Dear all,
> >
> >It's all in the macro. But when I run Gate I get the following 
> >errors:
> >***** COMMAND NOT FOUND </gate/output/root/enable> *****
> >***** Command ignored *****
> >***** COMMAND NOT FOUND </gate/output/root/setFileName MyRootFileName test1>
> >*****
> >***** Command ignored *****
> >***** COMMAND NOT FOUND </gate/output/root/setRootSinglesFlag 1> *****
> >***** Command ignored *****
> >etc...
> >It's obivious that the Root output doesn't work although everything should
> >be installed just right (see mail below)
> >Any other suggestions?
> >Greets
> >Els
> >
> >ps: the macro is in the attachement
> >
> >Dear all,
> >
> >Sorry, my fault. It should be "might" can't work with root output 
> >enabled.
> >
> >It may caused by difference between Redhat 8.0 and Redhat 9.0 (purly 
> >guess).
On
> >Redhat 8.0, it can't work ( two of my Redhat 8.0 Linux box can't work 
> >).
Redhat
> >9.0, I don't know, but I remember David Schottlander 
> >(dcs at robots.ox.ac.uk) had told me that there is no problem on his 
> >Redhat 9.0 box.
> >
> >Regards,
> >
> >Long
> >
> >Dear Claude,
> >
> >I can't run simultaneous OpenGL and root output either; please see 
> >the discussion "vis problem: Command not found".
> >
> >Best regards,
> >Simone
> >
> >
> 
> 
> 
> _______________________________________________
> gate-users mailing list
> gate-users at lphe1pet1.epfl.ch 
> http://lphe1pet1.epfl.ch/mailman/listinfo/gate-users
>


_______________________________________________
gate-users mailing list
gate-users at lphe1pet1.epfl.ch http://lphe1pet1.epfl.ch/mailman/listinfo/gate-users