[Gate-users] How to insert x,y,z axes

[Stathis Kamperis]

Hi again :D

Just for archiving purposes. The problem was due to the different
driver (OGLIX vs. OGLSX).

Cheers,
Stathis

On Mon, Feb 3, 2014 at 2:25 PM, Marc Chamberland
<MarcChamberland at cmail.carleton.ca> wrote:
> Hi Stathis,
>
> I have no idea why your axes show up like that. Have a look at what I did:
>
> https://www.dropbox.com/s/g5id2vtaml6i81v/gate_axes.tiff
>
> Good luck,
> Marc
>
>
>
> __________________________
>
> Marc Chamberland, MSc
> PhD candidate
> Department of Physics
> Carleton University
> Ottawa (ON)
>
> On Feb 2, 2014, at 14:13, Stathis Kamperis <ekamperi at gmail.com> wrote:
>
>> Dear Marc,
>>
>> thank you for your answer.
>>
>> I'm very confused as I can't get even basic stuff as axis drawing
>> working. For example I use the following visualization commands:
>>
>> /vis/open OGLSX
>> /vis/scene/create
>> /vis/scene/add/volume
>> /vis/sceneHandler/attach
>> /vis/viewer/set/viewpointThetaPhi 45 45
>> /vis/scene/add/axes
>> /vis/scene/add/text 1 0 0 m 100 0 0 X
>> /vis/scene/add/text 0 1 0 m 100 0 0 Y
>> /vis/scene/add/text 0 0 1 m 100 0 0 Z
>> /vis/viewer/refresh
>> /vis/viewer/flush
>>
>> and this is what I get:
>> http://dl.dropboxusercontent.com/u/25202446/opengate1.png
>>
>> I must be missing something very fundamental on how geometry and
>> visualization works.
>>
>> Best regards,
>> Stathis
>>
>>
>>
>> On Sun, Feb 2, 2014 at 6:32 PM, Marc Chamberland
>> <MarcChamberland at cmail.carleton.ca> wrote:
>>> Hi,
>>>
>>> Try the following instead:
>>>
>>> /vis/scene/add/axes
>>>
>>> This is from the User's guide section on visualization.
>>>
>>> Cheers,
>>> Marc
>>>
>>>
>>>
>>> __________________________
>>>
>>> Marc Chamberland, MSc
>>> PhD candidate
>>> Department of Physics
>>> Carleton University
>>> Ottawa (ON)
>>>
>>> On Feb 2, 2014, at 9:12, Stathis Kamperis <ekamperi at gmail.com> wrote:
>>>
>>>> Dear Gate users,
>>>>
>>>> I'd like to display x,y,z axes so that I confirm my geometry. I looked
>>>> up at the docs and I found:
>>>>
>>>> "/gate/world/daughters/insert 3axes"
>>>>
>>>> But when I actually execute the command I get:
>>>>
>>>> parameter value is not listed in the candidate List.
>>>> Parameter is out of candidate list (index 0)
>>>> Candidates : ImageNestedParametrisedVolume ImageRegionalizedSubVolume
>>>> ImageRegionalizedVolume box collimator compressedMatrix cone cylinder
>>>> eltub fictitiousVoxelMap general_trpd hexagone parallelbeam
>>>> parameterizedBoxMatrix regularMatrix sphere trap trpd wedge
>>>>
>>>> I also found a thread from 2010:
>>>> http://comments.gmane.org/gmane.comp.science.opengate.user/603
>>>>
>>>> where it says that this is no longer supported and one must use 3
>>>> dummy boxes. Is it true?
>>>>
>>>> Best regards,
>>>> Stathis
>>>> _______________________________________________
>>>> Gate-users mailing list
>>>> Gate-users at lists.opengatecollaboration.org
>>>> http://lists.opengatecollaboration.org/mailman/listinfo/gate-users
>>>
>